收藏本站
CS5460A
or custom calibration board. When the metering
Register.
system is installed, the calibrator would be used to
control calibration and/or to program user-speci-
fied commands and calibration values into the EE-
PROM. The commands/data will determine the
CS5460A’s exact operation, when the auto-boot
initialization sequence is running. Any of the valid
4C 00 00 14
74 00 00 04
E8
;Set Pulse Rate Register to
0.625 Hz.
;Unmask bit #2 (“LSD” bit in
the Mask Register).
;Start performing continuous
commands can be used.
3.3.2 Auto-boot Data for EEPROM
This section illustrates what a typical set of code
would look like for an auto-boot sequence. This
code is what would be written into the EEPROM. In
the sequence below, the EEPROM is programmed
so that it will first send out commands that write cal-
ibration values to the calibration registers inside
the CS5460A. This is followed by the commands
used to set (write) the desired Pulse-Rate Register
value, and also to un-mask the ‘LSD’ status bit in
the Mask Register. Finally, the EEPROM code will
initiate ‘continuous computation cycles’ data acqui-
sition mode and select one of the alternate
pulse-output formats (e.g., set the MECH bit in the
Control Register). The serial data for such a se-
quence is shown below in single-byte hexidecimal
notation:
computation cycles.
78 00 01 40 ;Write STOP bit to Control
Register, to terminate au-
to-boot initialization se-
quence, and also set the
EOUT pulse output to Me-
chanical Counter Format.
This data from the EEPROM will drive the SDI pin
of the CS5460A during the auto-boot sequence.
The following sequence of events will cause the
CS5460A to execute the auto-boot mode initializa-
tion sequence: (A simple timing diagram for this se-
quence is shown below in Figure 14.) If the MODE
pin is set to logic high (or if the MODE pin was
set/tied to logic high during/after the CS5460A has
been powered on), then changing the RESET pin
from active state to inactive state (low to high) will
cause the CS5460A to drive the CS pin low, and af-
40 00 00 61
44 7F C4 A9
46 7F B2 53
;Write to Configuration Regis-
ter, turn high-pass filters on,
set K = 1.
;Write value of 0x7FC4A9 to
Current Channel Gain Regis-
ter.
;Write value of 0x7FB253 to
ter this, to issue the standard EEPROM block-read
command on the CS5460A’s SDO line. Once these
events have completed, the CS5460A will continue
to issue SCLK pulses, to accept data/commands
from the EEPROM. The serial port will become a
master -mode interface. For a more detailed timing
diagram, see Switching Characteristics (in Section
1 .)
Voltage Channel DC Offset
MODE
RES
CS
SCLK
SDO
EE Read
Address 0
SDI
5460A
Commands
Stop
Figure 14. Timing Diagram for Auto-boot Sequence
DS487F5
25
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CDB5461AU BOARD EVAL & SOFTWARE CS5461A
CDB5466U BOARD EVAL & SOFTWARE CS5466 ADC
CDB5467U BOARD EVAL FOR CS5467 ADC
CDB5560-2 DEV BOARD FOR CS5560 W/SE INPUT
CDB5571-2 DEV BOARD FOR CS5571 W/SE INPUT
CDB8422 BOARD EVAL FOR CS8422 RCVR
CDB8952T BOARD EVAL FOR CS8952
CDCE906-706PERFEVM EVAL MOD PERFORMANCE CDCE906/706
相关代理商/技术参数
CDB5460AU-Z 制造商:Cirrus Logic 功能描述:PB-FREEEVAL BOARD FOR CS5460 - Bulk
CDB5461 制造商:Cirrus Logic 功能描述:EVAL BD FOR CS5461 - Bulk
CDB5461A 功能描述:EVAL BOARD FOR CS5461 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
CDB5461AU 功能描述:数据转换 IC 开发工具 Eval Bd Sngl-Phase Pow/Energy RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
CDB5461AU-Z 制造商:Cirrus Logic 功能描述:PB-FREEEVAL BOARD FOR CS5461 WITH USB - Bulk
CDB5462 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5462 - Bulk
CDB5463U 功能描述:数据转换 IC 开发工具 Eval Bd Sngl-Phase Pow/Energy RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
CDB5463U-Z 功能描述:EVAL BOARD USB FOR CS5463 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件